Bed Tilt/Mesh Clarification
Please help clarify for me.
Once you have done a bed level (I am using my beacon), "A", "B" and "C" are then level. No matter where I home Z on the board, the distance above or below for "A", "B" and "C" relative to "H" should be the same. These 3 points are level according to the probe and auto level.
From this point, I would see if my frame is skewed or bed is warped....
V-Core 3.1 400mm
Anyone know how I can make the mesh better? My printer is enclosed so I can't adjust the corners as the squaring video goes over. Due to the way the side panels must line up with the 3030 extrusions I am sure the printer is square so I am thinking maybe the bed was not the straightest from RR but I dont want to replace it. I tried placing a piece of foil between the magnet and pei sheet but those are too thick and causes a high point. I am open to any suggestions.
V-Core 3.1 400m bed mesh twisted near back of printer
I am running through the commissioning steps and I find that the back fo my bed looks twisted. Is this twist an issue with the frame not being square? or could it be the alignment of gantry/tensioning of the belts? I went through measuring the diagonals of across each side and i have less than 1mm variance over 80mm of distance on every side. I also am having difficulty measuring any difference in alignment so any guidance is great appreciated!
V-Core 3.1 500mm³ range 2.48
Hello are there any way to improve this mesh even more? there is a big bump in the back where it's supported by the bed arm and it falls down to the sides so my guess is its probably not frame nor rails related.
any tips on how i can improve this?...
VCore 3.1 500 high mesh range
Hey guys,
I'm currently struggeling a lot with my mesh on my Vcore as its pretty far out of range.
I installed the Spannsysteme X-Gantry right from the start.
I already followed the most instrucions given but still got about 0,5mm of range....
Taco, pancake, saddle... mesh
alright. I performed the enclosure 2.0 upgrade and now I've got a mesh that flexes from a Taco to relatively flat, and then to a Saddle as it heats. attached are three meshes, cold. heated 45min-1hr, and heated for 2hrs then loosened the x linear rail, and extrusion attachments and re tightened.
I'm still just barely under .5mm and it makes large full bed prints unlikely to succeed.
my frame is pretty darn square, and the only other advice I saw was loosen the linear rail and re-tighten. I've looked under the built surface and there is nothing pushing it up in front where I have the high spot. ...
my frame is pretty darn square, and the only other advice I saw was loosen the linear rail and re-tighten. I've looked under the built surface and there is nothing pushing it up in front where I have the high spot. ...
400mm 3.1 mesh
definitely not great.... but I haven't even tensioned the belts correctly yet. Just starting the thread now because I know I'll need it.
for the record this has a weird printhead that limits some area of the mesh which might lead me to some annoying troubleshooting....
move by 0.1mm for mesh alignment
attached is my first bed mesh after adjusting tension on a 400 enclosed ( panels not installed yet)
I believe A is back left, D is back right — Please correct me if I have the wrong interpretation of orientation.
B gantry attachment needs to move up 0.08 mm and
C gantry attachment needs to move down 0.16mm...
Enclosed 400: Low corner to saddle to wave to low corner infinite loop.
Hey all, any advice is appreciated because I am very close to 150 bed mesh attempts now and starting to lose hope 😅 .
I recently finished my enclosed 400 build and am attempting to run through the final calculations, but my mesh seems to follow this endless pattern of rear corners (pillar C then sometimes D) to a saddle to a wave (high in the front) to a low corner again and then this loop repeats infinitely no matter how much adjusting I do. I had finally managed to get a .190 (cold) at one point today but the moment I heated the bed it went back to .251
Specs: VCore 3.1 400mm enclosed, Eva 3 toolhead, igus chainflex umbilical, Spannsysteme lightweight x-gantry from fabreeko....
Enclosed v3.1 400 bed mesh advice
Just finished building my 400 and I am trying to get the absolute best bed mesh I can out of this thing. I watched the YouTube video that everyone references and got my bed down to .18-.19, but I feel like I can do better. As you can see from my mesh, my trouble is really just the right side of my bed. In the video he says not to move C up, but to push down on B. That didn't work for me too well and just made my mesh worse. I feel like it wouldn't be too hard to to loosen the drive cage at C, bu...
0.6 Range My Mesh Is Disgusting :(
I have been having troubles with this for about a year now and only just thought to ask. Its almost impossible to print bigger things.
New V-minion, bad mesh.
Ive just finished building my V-minion but this is the mesh.
This is my first bedslinger and there are no adjustments 😬
What kind of tolerances can i expect? Im used to being in the 0.150 and under range on my Merc....
Bulge on bed center
Hey people,
i have a bulge upwards on the mesh, so that either means that my bed is warped or my gantry is bowed down (or a combination of both).
Howe to fix that, or how to minimize the range of 0.2mm?
(I already checked if there is a washer on the magnet bed 😂)...
Mesh Range High... Frame or Bed?
Hi All,
What is a acceptable mesh Range on a 500 bed? I was hoping for a little better.
*Upfront info:...
Odd Bed Mesh
I've just noticed my mesh has been doing this recently, I am not sure what happened since i haven't really changed anything. I checked under the plate to make sure nothing was under there in that area. Not sure what else to check
Saddle shaped mesh
My mesh looks like a saddle. It's an upside-down uon the x, and a rightside-up u on the y. Is this a sign of a warped x-gantry? This is for a v-core3 500.
