What should I do about this?
This is a cold mesh of Vcore 400. Range is 0.174. The front seems mostly straight but there's an obvious slant to the two back corners which I have been unable to fix. Even if mesh range is okay this tells me something is wonky about the frame, no?
Edit: Reposted for higher res mesh and better pictures...
Printer not follow bed mesh
Hi guy. My printer doesn’t follow the bed mesh at all.
What I have done is just do the print start normally. (Of course, I did the probe calibrate and have the perfect Z Offset with Paper test)
Then the automatic bed mesh. And Load Bed Mesh Profiles to ensure.
Still. It still print too close to bed
...
im happyish with it... (is this good enough?)
this is cold bed. i layed everything down as flat as possible and weighed it down for a day with like 10kgs of weights. I 100% forgot to fix frame before laying down bed magnet..... is this good enough ???
Idea? Bedmesh is completely off world
Hello Together
I have been trying to set up my BedMesh for a few days now.
Unfortunately without any success....
Probed after heating shows upwards bow down the center
I managed to get the back corners within 0.021 of each other. However, when heating the bed, it warps. The warp is most noticeable in a line down the middle from front to back.
Biggest variance is in the back with the corners being lower than the center.
Leaving the bed heated for 10 minutes before probing in an attempt to get a more even temp throughout the bed makes no difference....
Bed Mesh gone mad
Hi guys.
My bed mesh after run with stock V3.1 400 is technically quite bad. And I am looking for improvements.
What I have done: BL Touch, BED Mesh Profile load = ratos at START_PRINT.
But still deviation is high. ...
Suggestions for getting a bit better
Hello,
I've been trying to get the corners a bit up.
Tried everything and still cant get better thant this.
Vcore 300, enclosed but without the panels right now....
Can't get rid of that middle dip
I already tried to fix this dip thrice. I even followed the video to re-screw the linear rails.
Issue with Bed Mesh
After even changing the X Gantry, and making sure its all snug and fit, to perhaps fix the valley, the bed is now double the worse, and I'm not sure why anymore.
Any insight is more than helpful. Thank you!...
Fix the dip :)
Any idea how to get rid of this dip? Thanks in advance 🙂
The printer is VCore 3.1 400...
Problem with ABL
I built a vcore 3 400 with 0.6 nozzle and BLTouch. I am trying to tune it but getting the first layer right is already a problem.
In the pictures (had to see), you can see that there are parts of the first layer printing well, parts where the nozzle prints way too close to the bed and parts where the nozzle is then too far from the bed. Shouldn't this be automatically compensated by the ABL....
Need some help with my mesh
I started adjusting it and I watched the recommended video. My back right is up so I have to get my front right down, right? In the video he said to slightly tap it with a hammer but if I do that nothing really happens. I had a dip in the middle so I loosend my x rail and now I only use 6 bolts and I think it improved, but what am I supposed to do with the left side ?
500 Bed Mesh kinda whack
I squared my printer while building it but then I brought it down from the 2nd floor to the basement.
Any ideas how to fix this? It’s not really noticable for small prints but when I do big prints, the nozzle would hit the bed real bad during 1st layer printing....
VC 3.1 500 valley
Since a while I can't seem to get a proper bedmesh (nor proper first layers) on my vc 500. It was working fine now for 1.5 years. Also I upgraded to 3.1 + added a CF gantry, however I don't recall if this was exactly the time this started or if it happened later on.
Screenshots show mesh after levelling with a super pinda on a self-made pertinax sheet & original RR PEI.
I'm somehow a bit clueless at the moment, I was suspecting the pinda as it sometimes stopped working on higher bed temps and ran into the nozzle, but not sure if that is really the culprit here. I can't imagine the aluminum base would sag like that? Any clues on that one? thanks....
Cant get this corner down
Any suggestions, I have watched the video referenced here a lot but I cannot seem to fix this?
Mesh issue with beacon
Firstly, the bed mesh variance is twice of my inductive probe
Secondly, the front half of the mesh seems to be very jagged while the back half seems fine.
Thirdly, the compensation applied is weird, front half of my print has good layer height but the back half is too high
I have calibrated the beacon sensor according to the documentation...
Saddle Bed Mesh - V-Core 3.1 500
Hello Community!
My Rat V-Core 3.1 500 is built up so far to drive first tests.
The Mesh looks not that good. And hast a range of deviation of around 0.5 mm.
Printer Data: - V-Core 3.1 500 mm - SuperPINDA / Beacon
Printer Build Skills: Beginner, already saw the "Mark"-Video, but uncertain if this helps alone....
