Rman
Rfinite commodity ever since 2022
CYes
TI want as much force as I can possibly get out of it, since no PC stick generates as much force as many real aircraft. Since the limiter setting felt to me like significantly more force than I get when settings are maxed I was wondering if there's a way to get more force out of it while using the stick normally. I don't expect there is, I just thought it was worth asking.
原I'm also curious about it too. So if every slider is 100%, would the motors produce their stated peak torque at the end of the travel?
WBasically at 100% spring the force is scaled linearly through the travel range (green line), you can also have a stiffer response, but saturated at travel edges (black line). The endstops have a very rapid rise of torque response vs travel giving the illusion of more force.
It's possible to increase spring gain above 100% using the spring "Gain Map" tool
It's possible to increase spring gain above 100% using the spring "Gain Map" tool
V:package: 
RHINO #0408 Has Shipped!
RHINO #0408 Has Shipped!V:package: 
RHINO #0409 Has Shipped!
RHINO #0409 Has Shipped!
Bthat might be my one, exciting times ahead it should arrive today 
原So in order to achieve the peak torque output (ex. 9NM for rhino/57BLF03) at the end of the travel, is it necessary to go beyond 100% spring gain? Will it cause any damage to the motor etc?
BThey'll cut out into protection mode long before they get any damage
WNo, motors do achieve peak torque at peak travel. And no, motors are pretty robust, the only limiting factor is the temperature.
原ok, thx for the answers!
LHi everyone,
i have a question for @walmis and the TelemFFB Devs (looking at @Number481
) What would you recommendation for a yoke be? Is there a good Project with the VPForce Kit? Or is there a way to use Brunner Yokes with TelemFFB?
thanks!
i have a question for @walmis and the TelemFFB Devs (looking at @Number481
) What would you recommendation for a yoke be? Is there a good Project with the VPForce Kit? Or is there a way to use Brunner Yokes with TelemFFB?thanks!
NLast question first, no, the Bruner won’t work with TelemFFB. The driver is very custom to VPForce.
If you search around, a few people have attempted yokes. I am not qualified to give mechanical design advise, but if I were going to try, I’d rip apart my Alpha yoke that has been collecting dust under my desk for 2 years and see what I could make out of the guts.
If you search around, a few people have attempted yokes. I am not qualified to give mechanical design advise, but if I were going to try, I’d rip apart my Alpha yoke that has been collecting dust under my desk for 2 years and see what I could make out of the guts.
V:package: 
RHINO #0410 Has Shipped!
RHINO #0410 Has Shipped!V:package: RHINO #0411 Has Shipped!
RHINO #0411 Has Shipped!V:package: RHINO #0413 Has Shipped!
RHINO #0413 Has Shipped!V:package: RHINO #0412 Has Shipped!
RHINO #0412 Has Shipped!
TAnybody know if/when the VKB adapter will be updated to match the new VKB RevC connector that is now the standard? That’s what is on the current Gunfighter Mk4 sticks and the Gunfighter Mk3 base.
Xlast time i checked order page, it had RevC, might be wrong tho, check it out
X
Aisn't that the old standard
Aat least I thought the new one would be completely different
VThat picture is Rev B, not C. C is new one with TRRS type connector, they've gone away from pogo pins and pads.
Xoh sorry, then i'm wrong, i thought this was latest
V:package: 
RHINO #0414 Has Shipped!
RHINO #0414 Has Shipped!V:package: RHINO #0415 Has Shipped!
RHINO #0415 Has Shipped!
MStill targeting early next month for the next mfg mod announcement, Walmis? Or did the supply issues not get relieved?
Iany of you knows the dimensions of the VPforce Shift-Register Board?
S20x45mm
GIn DCS how do the settings in the configurator interact with what DCS is giving?
Does making changes in the configurator settings and effects change anything in DCS at all?
Does making changes in the configurator settings and effects change anything in DCS at all?
NConfigurator sets the max capability for a given effect type. A sim can send the FFB command for “%50 spring”. That will be %50 of whatever your configurator spring settings are.
GDoes that work the same for all the settings and effects?
NYes. Some modules also vary the amount of dampening on the controls. The resulting force you feel will be affected by the damper settings in Configurator.
Same goes for all the stuff in TelemFFB. Most of those effects are "periodic" type. So while you can adjust each effect individually in TelemFFB, they are all really "% of configurator value"
Same goes for all the stuff in TelemFFB. Most of those effects are "periodic" type. So while you can adjust each effect individually in TelemFFB, they are all really "% of configurator value"
GThat may explain the issue I'm finding with the apache, I have an offset grip so have -5.5% static force and that allows the stick to centre perfectyl for every module........ except the apache which seems to want -2.5%
Is there anyway to change profiles/settings based on module?
Is there anyway to change profiles/settings based on module?
NYou can dynamically load configurator profiles per aircraft with TelemFFB
GAh cool, found it. Didn't relate the two I had assumed that was a settings file for TelemFFB itself...
Thanks
Thanks
SI know I’ve asked a few times but I’ve finally finished my move. Does anyone have any budget friendly Rhino compatible rig recommendations? I love the 80/20 style. Happy to build my own if there are plans too.
HMine is side mounted with Monstertech mounts. Whether you consider that budget friendly though 
SI tried desk mounting but my desk isn’t that strong and it limited me. I do want a full rig style one. I like the racing sim ones just without the angled racing chair and with actual mounting options
HYeah, desk mount won't cut it, mine's still chair mounted and that works well
SOh I see!
SI’ll consider it but I rarely fly anything with side mounting
SThe main thing I fly is going to be the Phantom
HYou get used to it, even on planes that should be center
SAnd then the Eurofighter when thats out
Ftrack racer, sim labs, race anywhere
SI think I had a GT1 Evo back in my simracing days. Tempted to get another one and work out how to make it for flight sims
