Ouchmaster
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 4/24/2024 in #fix-my-resonance
Recommended shaper MZV - Vibration 6%
Using a Vcore 500.
Smoothing at 0.09 - recommended speed 6300.
Any issue using this shaper with a vibration of 6% ? I mean in terms of quality of print and printer health.
Many thanks
2 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/5/2024 in #fix-my-print
Large print warping issue
![No description](https://answer-overflow-discord-attachments.s3.amazonaws.com/1204170585723117668/20240205_220036.jpg)
4 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 10/30/2023 in #ratos-support
Moonraker is not permitted to restart service 'RatOS'.
Moonraker warning
[update_manager client RatOS]: Moonraker is not permitted to restart service 'RatOS'. To enable management of this service add RatOS to the bottom of the file /home/pi/printer_data/moonraker.asvc. To disable management for this service set 'is_system_service: False' in the configuration for this section.
Should I SSH in the Pie or should I go to the moonraker.conf file in Ratos os to make the change ?
What lines should I add ?
Thanks.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 8/28/2023 in #fix-my-printer
heating shuts if 1 second after prime line
![No description](https://answer-overflow-discord-attachments.s3.amazonaws.com/1145810413733294100/20230828_215913.jpg)
3 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 8/16/2023 in #fix-my-resonance
Spikes at high mghz belt tension
![No description](https://answer-overflow-discord-attachments.s3.amazonaws.com/1141448156027043900/rn_image_picker_lib_temp_e019d75b-4d15-4bf1-924f-9acd63ed1582.jpg)
4 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/27/2023 in #fix-my-printer
Heater disconnected from heating block
![No description](https://answer-overflow-discord-attachments.s3.amazonaws.com/1079912637602742342/20230228_004017.jpg)
8 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
![No description](https://answer-overflow-discord-attachments.s3.amazonaws.com/1076212605703704696/20230217_194302.jpg)
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 1/4/2023 in #fix-my-print
pressure advance issue ?
![No description](https://answer-overflow-discord-attachments.s3.amazonaws.com/1060278694444281956/20230104_202539.jpg)
9 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 12/27/2022 in #fix-my-printer
layer shift when increasing or decreasing printing speed
Title says it all. I have no layer shift if I do not increase the global speed mid printing, however I do, lets say increase global speed by 50% then at that point layer shift is very noticable and stays the same until the end of the print.
Is that normal ?
1 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 12/27/2022 in #fix-my-print
Two tone print breaking at new color start
![No description](https://answer-overflow-discord-attachments.s3.amazonaws.com/1057351046160187392/20221227_182528.jpg)
5 replies