Ringing on only one side of the print?
Whenever I print a flat surface on the y axis, one side has terrible ringing and resonances, while the other side is perfect. It seems to only happen on movements when the printhead is moving back, not forwards, so I think its an issue with direction. Could this be a motor/driver related issue? The issue doesn't show up on any of the other sides, so i doubt it
The picture shows two different sides of the same print, both on the y axis.
i recently changed my cable chain to a USB, but the issue didn't go away, so I'm guessing its not that....
Superslicer general config help...
Need some help, just jumped from Cura to SuperSlicer for V-Minion as it looks like best option by many users...
I've gone through all set up using as a base RatRig's standards and modifying some to higher speed where needed,
start to print and speed is way off what I have set in slicer and accelerations change at its own.
Could somebody give a look at what I might have wrong?
Thanks, (edited)...
Ugly ASA print outer layer
Having problem getting a consistent outer layer with ASA.
Have played with EM 91-95 and PA 28-45
Temps are 255 nozzle and 105bed chamber in 70-75
Cpap fan 16% normal 20% bridges....
Gaps at the seams
Hi! I have been getting these gigantic gaps at the seams (aligned), can somebody point me to which settings I should fiddle with?
Filament: DAS PETG
SuSl with standard RR settings for 0.2 mm HF and Generic PETG at 245° C....
Tuning
Hei i have a lot of stringing and a bad wall finish near edges (using rapido and LGX, part is with PLA) any sugesstions? Any good profiles for Prusa Slicer? 😄 THANKS A LOT 😄
Z dimension undersized
I noticed that on all of my prints that my Z dimensions are undersized. For example, something that is supposed to be 38mm is 37.25mm. I also did a double wall test, where the walls are 100mm and 50mm and a height of 10mm. The x/y comes out to 100.04mm and 100.14mm and 50.15mm and 50.35mm. However my Z comes out to 9.7-9.75mm. Any idea what I should tweak?
solid walls coming out looking like a chain link fence.
I just got my rat rig set up. Vcore 3.1 with 2.0 enclosure running reprap on a duet 3 mini 5 plus.
My printer is extruding weird. I just calibrated esteps so it extruder exactly 100mm when I tell it to.
Anyone have a similar issue and know how to fix it?...
strange pressure advance behaviour
Hello,
I was running a pressure advance tower, but the pa did not seem to improve or change the bulsging edges. In the first picture, the pa was at 0.06 according to the console. In the second picture you can see the seem. I assume there is an other paramter I should be looking at?...
Print curls up into nozzle
Been having this issue on some prints where the print will curl upward into the nozzle, getting browned/blackened. It usually only happens on the side facing the back of the printer. I assume this is a cooling problem, do I need more cooling or less? Should I direct the duct differently?
petg not printing with pla speeds
Hi,im having trouble printing pet g at my normal pla speeds,the temps are 250 nozzle and 70 bed,the fillament is polylite petg,this is how the print looks
PETG layers not sticking on layers with high infill
I have a part I'm printing with Overture PETG (printed from a drybox) and I'm having an issue where whenever I'm at a layer with a high solid infill the perimeters just completely fail. I think the main issue with this is that, since a large portion of that infill is considered bridge infill, its moving really slowly (i decreased bridge accel and speed by a lot to improve bridging, which worked), these layers are taking a long time and some filament is cooling too much. How can I fix this error?...
What would cause this?
Other than shown, this print is a great print everywhere else... printed at 0.1 layer height.. trying to fine tune finer prints.. anybidea what the issue was here?
[Fixed] V-Minion Z or Y axis issue
Any thoughts on the cause of these lines on my v-minion? They are about every 4mm and on the front and back only running along the x axis. The sides are clear.
PLA bubbles up on bed.
I keep trying but this Esun Marble PLA bubbles up. Esun rates it at 190-220C
I’ve tried cooler / hotter extruder , cooler hotter bed 70-90C
Raising nozzle, lowering nozzle ( as you see in the lines here )
Reducing flow to 95%
Reducing speed to 20mm/s...
do i have too much cooling?
Did the EVA 3 dual 5015 upgrade on my minion recently. using a matte black pla around 240 and capped flow at 25 with my dragonfly and cht 0.6.
Almost perfect print just a few boogers.
Thoughts to what it might be?...
Weird layer lines in print - overextrusion?
Hey, I have really REALLY extreme layer lines. I don't have stealthchop or anything, it's just weird. Might be current to steppers, might also be overextrusion. Stepper current is set to 0.8 for ender 3 style stepper motors which according to my googling is about right. Retraction is set to 0.5mm and 25mm/s
warped holesextra holes
Im printing the parts in abs for a enclosed ratrig printer, and some parts have these warped holes and not connected walls where they should be connected, we have a enclosed ender 3 v2, but the doors swing open right before a print, so we close them pretty soon. Could that be the issue? (Second pic as a good part for comparison) help would be much appreciated.
