Bed dip
Do i need to order a new bed this 0.5mm variance seems extreme, 3 layers to fill the gap of where i normally print
SuperPINDA (z probe) Always Triggered
SuperPINDA is connected to an Octopus Max EZ as described in the ratrig documentation and the BTT manual (which both agree with each other). Left to right wiring is: Black (switch), Blue (ground), Brown (+5v).
Upon powering switch, I get a glowing red LED from the SuperPINDA. Multimeter readings show a steady +5V between brown (+5V) and blue (ground). Without a piece of metal under the probe, there is zero volts between Black (switch) and blue (ground). Holding a piece of metal under the probe results in the red LED dimming, and 2.3V between the black (switch) and blue (ground) wires.
Regardless of there being a piece of metal or not under the probe, it always reads as "triggered" or closed in Klipper....
Upon powering switch, I get a glowing red LED from the SuperPINDA. Multimeter readings show a steady +5V between brown (+5V) and blue (ground). Without a piece of metal under the probe, there is zero volts between Black (switch) and blue (ground). Holding a piece of metal under the probe results in the red LED dimming, and 2.3V between the black (switch) and blue (ground) wires.
Regardless of there being a piece of metal or not under the probe, it always reads as "triggered" or closed in Klipper....
Ratrig Bedmesh looking aweful
So i finally built my ratrig 500 and i'm unhappy with the bedmesh, any help on how to fix it ? thanks
Z1 stepper overtemp error.
Hi. I've just started getting this error. I don't know why. I've checked the stepper drivers. I've checked the temp (motor and driver are cool) and I've checked all the connections. I've also swapped stepper drivers and it still ends up being Z1.
I only seem to get this when I run shaper_calibrate. If I print, everything is fine.
...
4P Part cooling Fan, Config problems
Hi guys,
I have a problem with setting up a FAN in the Printer.cfg of my Minion.
The FAN stops from 0-10% again. From 10-100% it runs, but with fluctuation in speed. You can also hear how it runs faster and slower.
...
VCore 3 End Stops Not Electrically Closing?
Hey all, I'm wondering if someone could help me understand the limit switches (end stops) that came with my rather old VCore 3.0 kit. Specifically, it doesn't seem like my switches actually close the ground and signal pins when physically triggered and probed with a multimeter. Maybe I'm not understanding things with the LED function though...
Background: I'm wiring up a Manta M8P (1.0) so am following https://os.ratrig.com/docs/boards/btt/manta-m8p. Checking my limit switches in klipper they never change state when physically triggering the switch (the LED does shine when triggered though). I then noticed the warning on that page that the switches "probably" need to have their white (notionally signal) and red (notionally 5V) lines reversed on one side of the cable so I did that for one axis to test but still don't see any movement on the switch state. Removing the switch and jumping the white (signal) and black (ground) lines leads to klipper telling me they triggered so I know my pinout / config is OK. I then probed the actual switch(es) with my meter and don't see any contact when the switch is closed between the signal and ground pins.... is that expected? Is it possible to burn out the little switch circuit?...
Homing problem with "ratOS_homing" not valid section
Hi there.
I installed Klipper on a pc with Kiauh on a Ratrig Vcore 3. I'm having issue with the ratOS_homing section which is not considered valid. The z homing is not being done in the middle of the bed, i have to manually move the head to the center of the bed otherwise the head crash into the bed.
I have a second problem with the shell-macros file and especially with shells command-generate_shape_graph. I found the methode to relink this macro however i cannot connect to http://ratos.local/configure, because i'm not on a pi, mayble...
https://os.ratrig.com/docs/troubleshooting/#section-gcode_shell_command-generate_shaper_graph_x-or-others-is-not-a-valid-config-section...
SD card seems to be full
Back again sorry. For some reason there is only 80 meg left on the SD card. No idea why. I am not running a camera although I did have the timelapse active. There were no files in the timelapse. I cleared out old print files. Can anyone point me to what might be taking up all of the space. Thank you!
