Keep adjusting or leave it alone?
VCore 3.1 500 w/ v2 enclosure, based off what ive seen posted before I should stop adjusting and let it be correct?
Loose bolt or something? VCore 3.1 300
Hello mates,
What do you guys think of my belts and resonance?
I think I might have a loose bolt or something.
Even if the tension seems ok. ...
V-core 3.1 400 full metal mod. Looking kinda clean.
Should I touch anything or just leave it as is? I am kinda happy with how it looks and dont want to mess up something.
V-Core 500, Y-Resonance, Duet RRF
Hey all, i have all but eliminated the resonance in the x axis, my belts are equally tensioned measured via the tensioner tool. All thats left is some minor ringing in the Y which if i can fix i would love to. I use Duet so i have not been able to quite compare my readings with you all but if there is anyone who can help me decider any issues in my vibe tests id appreciate it
[v-core 3.1 500] Further Tuning Advice
I have spent the past couple of days resonance tuning my newly-built VC3.1 500 and I do believe I have gotten my belt tension graphs and resonance to be decent at this point.
However, I have noted that the belts do still slap a bit against the frame at their peak resonance frequency and was wondering what the optimal solution to actually verify that the absolute belt tension is about what it should be.
After doing some tightening of both belts, I have been able to generate the attached graphs. I was wondering if it is worth chasing any further tuning, or just going with what I got, using MZV with the provided profile and playing with acceleration limits from there....
VC3.1 500 issues. FMMM and Extrusionless X
I have recently built my second VC3.1 500 and have added FMMM and an extrusionless X. My resonance and accelerations are quite a bit lower than the first machine I built and I'm scratching my head as to why.
The tool head doesn't move at all when I manually move the gantry forwards and backwards, the belt does walks up and down a bit on the pulley but it doesn't seem to be chewing it up. Checked all bolts and tried to keep the umbilical cables tight. They're in a nylon sleeve with 1mm piano wire. The machine is sitting on a table but it's pretty sturdy... I will try and put it on the floor and test but anything else I should look in to? Thanks!...
Resonances on y axis (v-core 3.1 300) are horrible, it's driving me nuts.
I've been trying to tune my belt tension and get rid of resonances for a week, and I feel like I'm getting nowhere. I managed to get the belt tension to a point that I thought was "good" , and then ran the resonances graphs for input shaper. X doesn't look too bad to me, but y is an absolute mess. I've checked for loose screws, and anything that may be vibrating, but I can't find anything and I'm getting desperate. I would appreciate it if anyone more knowledable than I would lend me a hand, as...
bad input shaper after change eva3
Hi, yesterday night I’ve upgrade my Eva 3 (by RR) with eva3 with heat insert (asa) and joiner xy in asa. why today i have 2 peaks in input shaping?
Vcore 300...
Wierd looking chart
So after having giant ringing problems I did input shaper.
Red one looks almost perfect to my eye and the small spike later is propably because of not attached cable. But the second one looks quite bad to me. Im by no mean an expert in input shaping.
What could cause this and how to fix it?...
VC3 500 w/AWD
I just stalled AWD and when checking input shaper, I'm getting poor results. Wondering if it's a binding issue or something else. If it is binding I haven't figure out how to fix it. Been adjusting belt tensions and that's about the best I can get.
V core 3.1 500 bad graphics and jerky
Hello everyone, what could be wrong with my machine, it's a v core 3.1 500 and I've already done some things trying to improve my input shaper graphs but I can't get them like the others, (clean and with well marked peaks), what Could it be wrong or what can I improve?
Horrible ghosting
I get very bad ghosting at any accel and speed. Even if I go at 50mm/s 500mm³/s. What could be the cause? Its also same bad on X and Y.
Input Shaper results are inconsistent
I changed my Layer Fan setup so rerun my Input Shaper calibrate. Just for fun I ran it four times and was surprised there are different results each time. Is this normal or is there something wrong with my RatRig?
First graph
I had my ADXL running and input shaping applied but never generated a graph. Then I had to get a new ADXL and loom and here I am, new test and remembered to make the graph. I got it to apply and I don't really see any ghosting on my test prints, but here are my janky graphs.
