ToolHead Front Printing
Hello Everyone,
I have an issue for printing the new toolhead parts. I have some holes and I can't find the setting.
I sliced the parts on Superslicer and orca 1.7. And a friends slice it with the same issue.
I am thinking about an issue with the wall wide of the files
Can some one help me ?...
esun epa cf Problem
Hello, I have an issue with my 3D printing. It only occurs with the EPA CF material; all other 3D print results are error-free. I’ve already adjusted the flow rate, but the problem keeps happening at regular intervals. What could I try to resolve it?
Switched to 0.6mm nozzle, rough time of calibration
I put in the 0.6mm nozzle that comes with the Rapido 2 and I'm trying to calibrate everything. I'm hitting some problems that I can't seem to figure out, though. Anyone have any thoughts/tips/0.6 profiles?
- Red: This is the edge that the z-seam is on. It seems to have a chunk out of it. I have tried to calibrate the Pressure Advance. The other corners seem fine, just the one with the seam. It's currently set at 0.017 (it is 0.025 for my 0.4 mm nozzle).
- Yellow: The edges don't appear to be straight. There's a bulge in the middle, most visible on the corners. I've tried messing with the extrusion percentage and the line widths, but it doesn't seem to completely go away.
- Green: There are some small gaps between the top infill and the perimeters. If I bump the extrusion up enough, those close up, but then the surface on the top is rough due to being over-extruded....
over extrusion and under extrusion on the same print
Hi all,
I have a print that on one side is over extruding almost to the point of failing and on the other side has areas that don't have enough extrusion.
Seems like too much plastic on one side of the print and not enough on the other.
...
Inconsistent First Layers vcore 3.1 w .6mm nozzle
I did the first layer test print yesterday after calibrating the probe offset. I eventually adjusted the z offset until the top surface of the first layer test was very smooth, let the print complete, and saved the adjustment to the config. Today I went to print a calibration cube, and the skirt and outer perimeters of the cube's first layer printed horribly. About halfway through the solid infill portion of the first layer it suddenly turned smooth again and the print completed properly. Attach...
Second Hand 3.1 with 0.8mm Nozzle not printing
Hello everyone its me again! I hope this saga has almost come to an end! So after finding out that the printer does not have its standard 0.4mm nozzle but a 0.8mm nozzle instead. The test extrude function works fine but when it comes to printing the gcode the filament just balls up next to the nozzle.
Warping at support interface on large print
I eliminated any warping at the bed, but now the print is warping where the support stops.
Should I consider tweaking support settings to try to avoid this issue or will this be unavoidable?...
holes in print
What parameter schould i change to close holes in print. Orca slicer, vcore 3.1 300x300x300, 0,6 dyse, petg
Gear like pattern on some round shapes
I have a strange phenomenon with my prints: Printing at about 120mm/s there are gear shaped patterns on some round shapes. So far ONLY in more complex models.
They appear on:
Holes, cylinders (outside), rounded edges all in X Y, all around
...
PLA overhangs are utter mess
OK. Dunno what I'm doing wrong. But this is what I get from overhangs. 200C, 60C bed, 4028 fan on 50% overhang printed at 33mm/s
Any questions, anything, I can add. please, shout ..
It's like the PLA "doesn't stick" .....
Print got messed up midway
I was printing this vase and up until about 80% it printed perfectly but then it got messed up. Can anybody help me figure out what the problem that caused this is and how to fix it?
Gaps at end of perimeter
My print experiences gaps at the end of external perimeters. It appears to line up with my seams and retractions, however it does not go away if I disable retractions (set retraction_length to 0 in Klipper. I have firmware retraction on).
I use Superslicer. I have seam_gap[0] = nil
any pointers in the right direction are greatly appreciated....
layer cracking
I am printing a large print and am getting cracking between layers.
PLA printed solid Jessie filament
Hotend at 210°C and 220°C
Bed at 50°C
0.4 nozzle with 0.2 layer height...
Weird filament extrusion
I have this weird extrusion on the corner of my prints. I dont know what to change to correct this.
Nylon cf-15
The filament is being actively dried. Although how dry it currently is. Could be up for question. What would your bear guess be this is? I have not tried anything yet as I’m not much of a print quality person. But I would like this gone.
Lines in X movement
Hey,
I'm currently printing some boxes on my V-Minion in vase mode, the sides that are printed on the X axis have strong waves that you can see and feel, on the sides of the Y axis everything is smooth
Checked everything but all looks fine ...
Endless Layer Shifts
I’m at a loss. I keep getting these awful layer shifts and I can’t figure out why. It seems to be getting worse and worse. I tightened the belts and this is what happened. I really could use some help. Vcore 500mm
First Layer defects
Hello all,
Could use some advice on my first layer. Getting these "boogers" on top of my first layer and can't figure out what's causing it. It's sticking up high enough the nozzle runs into it and potentially causes a layer shift
Printing PETG at 235C with a Mosquito hot end and Orbiter extruder. I have gone through calibrating my motor for the extruder already...
