RRC

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!

Join

RRC

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!

Join

ratos-support

fix-my-print

fix-my-printer

fix-my-resonance

fix-my-mesh

german-support

MACBEAN

4/13/2023

Extruder heater not heating at expected rate

I've had 1 successful print out of this printer now it's throwing up errors like this about 6-10 layers into a print, is there something I'm doing wrong? I've tried to read the klipper log but all it tells me is that the temperature goes down. Log and screenshot of problem attached.

lillian

4/12/2023

motor return error code

when trying the first start up of the printer following the procedure i tried to over ride he motor with "SET_CENTER_KINEMATIC_POSITION" to check their movement and i get a error and the return: TMC 'stepper_x' reports error: DRV_STATUS: c0130010 s2vsa=1(ShortToSupply_A!) cs_actual=19 stealth=1 stst=1 i checked the wires and the plugs both side are good... more over the gantry was, as i first talk about in "sticky axis" post of @gsieben, kind of hard to move i rechecked as recommended on that post the diagonals and they are both equal ... i dont understand either problems and their relations...

lillian

4/12/2023

end stop and probe shenanigans

hello i am kind off clue less on a problem i have with my new config: ratrig vcore / octopus v1.1 / euclid probe / raspberry pi4 // all on mainsail the problem is after the initial programation when i got to checking endstop (i followed the klipper procedure) they returned: all triggered. i proceded to check if it was a state inversion with: QUERY_ENDSTOPS , and the result is the real problem: Z (euclid probe) return triggered manualy activated or not....

deep-jade

4/12/2023

There's something I don't understand about the RATOS 4028 FAN guide.

Hi I'm trying to follow the Ratos guide to prevent the fan from running when the power is turned on. My boad is BTT Octopus v1.1 Does the following explanation mean to connect to PA9?...

SgtKiLLx

4/11/2023

having all sorts of issues

i didnt have issues yesterday., now today, prints arent sticking. i did the popcan under the x gantry to level it, and my mesh is still messed up.

harsh-harlequin

4/10/2023

mistake on v-minion

Hello guys. I’ve few questions about v-minion. I am configuring my firmware....

Chrizzar

4/10/2023

V-Core 3 Rapido UHF + LGX Lite. Constant issues with filament not extruding/getting stuck in hotend.

So far I have took the printhead apart multiple number of times (at least 10 times), to fix this issue. It happens almost each time I want to switch out the filament.. It keeps getting stuck right at the opening of the hotend, where the ptfe tube meets the hotend.. It does not help pushing filament through, it is is still stuck. It happens a lot and I'm getting very tired of it. Can anybody help me to fix this issue?...

deep-jade

4/10/2023

4028 fan 99-100% big difference

Is it normal to have such a big difference between 99 and 100 fan power? Thanks...

flat-fuchsia

4/10/2023

Probe triggered or open all time

it always stays open or closed, it is the inductive probe that comes in the recommended kit, the wiring is done as it is in the guide. the probe lights up red

MACBEAN

4/9/2023

Pi keeps dropping wifi and sometimes doesn't connect on boot

As in the title

inland-turquoise

4/9/2023

V minion Eva 3.0 sensorless homing problems

I have upgraded my minion with eva 3.0 with dual5015 fan duct now my printer is homing with the fan duct on the x motor mount and its printing to far right i would say 5 mm or something like that can anyone help me or say me the new x value for this problem

genetic-orange

4/9/2023

power cut, now printer is locked in place

Had a power cut, and because the RatRig doesn't even have power recovery, infant continue the print. But right now the printer is locked in place. Can't move the X axis without homing the printer, but it won't be able to home itself with the print still stuck on the print bed. Any way to bypass being able to move the z axis without homing the system?...

MACBEAN

4/9/2023

Part cooling fan running full speed at 0% and homing issues

I have the delta PWM fan set up as close as I can tell to what douzuki says in their build instructions but when set to 0% it appears to be running at 100% and vice versa secondly, im unable to home as y goes in the wrong direction, and when reversed goes all the way back and then and doesnt stop on the endstop and continues to drive left...

extended-salmon

4/9/2023

is it normal the the 4028 fan can't run under 40% ish

i have the fan wire up like the guide but the fan can run below 30-40% duty is this normal and if not how might i fix it?

hikerjim

4/9/2023

z tilt issue

So I think I almost have my printer fixed except 1 issue. Its kinda odd, but here is what is happening Once I get bed leveled old fashioned way, and do probe_calibrate I kick off z tilt. Comes to front left, fine Moves to back all is fine Then moves to the front right and does the initial probe...BUT and ONLY on this step when its lowering the bed to move over to the front left 2 of the 3 z motors stop, the front right seems to lower another 1/2 to 3/4 rotation....

hikerjim

4/8/2023

x endstop cable

so in trying to find ongoing issues, i noticed the cable on the x endstop is hot, I just unplugged it, but why/what would cause the cable to get hot?

hikerjim

4/7/2023

need advice on issues I`m seeing

Hello all, I'm hoping someone can give me any idea about what I have going on. I'm seeing many just odd and strange behavior that I'm at a loss for what is going on. I'll start with the list of odd things, then I'll give my list of things I've replaced. At random times, with print head anywhere and I choose to Home all axis, it moves on x axis just a couple of mm stops and says no trigger on x after full movement. If Homing actually works, (there's a reason for this and explain later on..) I run probe_calibrate, then z tilt. This is all after i level the bed manually. When I run z tilt it will go through and 1 or 2 things will happen. 1 - it will go around and eventually give up or 2 - while actually watching the z tilt run another time, the rear and front right will raise the bed but front left fails to raise....

Mietzekatzi

4/7/2023

Acceptable Amount of Bend of Leadscrew?

Hi, I believe that one of my leadscrews has a slight bend, which can be seen when turning it. The first video is with the bed arm close to the bottom, the upper end of the leadscrew is uncontrained. Here you can see that the end of the leadscrew shifts position when rotated. ...

Bameron

4/7/2023

Belt issues

The belts on my 500mm vcore 3 are moving up and down, and griding against the idlers, causing squeaking noises. I'm not sure how to fix this, and ive rebuilt the gantry with new idlers many times. There seems to be a bit of artifacting caused by this, so I would appreciate it if someone could help me out....

hikerjim

4/6/2023

Rapido plus hotend

Has anyone installed a Rapido Plus on their ratrig yet? I had a big ...not sure what to call it, but had to reprint EVO parts and get a new hotend. I upgraded to the all metal Rapido Plus but something isn't right. It's not reading the temp correctly. I've replaced all the wires and no change. So that leaves 2 things, the board is damaged or 2 something special about the Plus that I don't know about. As soon as I turn the printer on and without doing anything it reads it at 159C, which I know isn't correct. Thanks Jim...

Previous Next

Gaming

Programming

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!