Enclosed v3.1 500 is it enough?
greetings, I think I've been trying for 4-5 hours and this seems to be the best I can do. is there any advice? :mildpanicintensifies:
Solution:
Yes,I have a 500 also and there is a lot of change between 0 and 110. Try heatsoaking for at least an hour at the temperature you will be expecting to print. BTW, your last one is certainly acceptable.
new idex build mesh 400 enclosed
Just got my printer making some moves. It’s my first own-built printer and I just ran a bed mesh using a beacon3d.
Do I need to correct this error or just be happy and move forward? What’s a good value ?...
should bed leveling be this tilted?
I've just set up my vcore 3.1 400mm and run the bed mesh, and I get this very titled bed mesh. (I haven't printed yet and I haven't seen it level the bed with the 3 points that I've seen it do on other people's machines) I feel like if the left Z would raise a bit it would solve my problems? I tried to fix the frame a bit but it doesn't fix this tilt. I'm using the standard 3.1 - 1.4 kit with the super pinda probe.
Need Advice/Sanity Check
Am i right, that i can fix my mesh by pulling the front Extrusions up from the Y Axis ?
Best
RR V-Corer 300...
Mesh v-core 3 400x400
any suggestion to which rail i should try to move up or down?
it looks kinda flat except the back left corner :/...
Bed mesh falls off a cliff in one corner
I have beacon running a bicubic 32x32 grid on my 500mm bed. It looks like at the HIGH-Y/LOW-X corner it falls off a cliff for some reason. Should I pad this with paper or something? Not sure how to approach this.
Hello i need some help
Hello all after some relocating and rebuilding of my ratrig 500 I wonder if some could help me After a lot of changes from the video bolting and unbolting etc i am stuck with this.
I can't move it anymore and if i manage to move it somehow the right corner will move down and stuck with a weirder mesh. any help would be apreciated thank you....
Cannot smash this corner any more.
I have tried: adjusting front left down, won't go any further. raising back left up. shimming the back left up just exagerated it across the entire rear edge. halp i need an adult.
V-Core 3.1 400 with bent X-Gantry?
Hi,
I set up my first self-built printer today. Most of the time I spent on getting a reasonable mesh. After I had no success with changes to the frame and everything looked the same, I temporarily placed paper under the X-Gantry, and it worked... That doesn't look too bad? Now the question arises whether I should replace the X-Gantry or use shims? What do you think? Thanks and regards...
Vcore 3.1 500 IDEX
Think I got my frame square. The range of 0.255 mm is not bad, there is however still a saddle in X-direction.
With advise from the attached YT I have already loosened and retightened lightly the x and y axis screw's and checked the rails for flatness. This makes no difference.
Can this be further improved or is thsi the best I can get?...
Is this the best I can do ?
This is the bed mesh of my vcore 3.1 500 with the bed heated to 60°C. After this mesh I ran the bed mesh a couple of times and the variance was around 0.220. I think this is the best I can do. What do you guys think ?
Frame Adjustment advice
Hello guys,
After running a bed mesh, I have this problem: deviation is too high. So which position should I change ?
Note that 0,0 is Front Left and the Highest point is Back Left Corner...
bed leveling not working?
The bed leveling seems not to be working properly, as in some places it is too low and in others too high. Should be it compenseited?
Bed Tilt/Mesh Clarification
Please help clarify for me.
Once you have done a bed level (I am using my beacon), "A", "B" and "C" are then level. No matter where I home Z on the board, the distance above or below for "A", "B" and "C" relative to "H" should be the same. These 3 points are level according to the probe and auto level.
From this point, I would see if my frame is skewed or bed is warped....
