Extruder Temp Error in the Middle of a print
Im getting the following error mid print. Im guessing my Rapido is going out, if anyone knows anything would appreciate it
MCU 'mcu' shutdown: ADC out of range Sensor 'extruder' temperature 327.031 not in range 0.000:300.000 This generally occurs when a heater temperature exceeds its configured min_temp or max_temp. Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software. Printer is shutdown...
Missing 100mm on Z height on Vcore 4 500
Hopefully this is an easy one but I just realized when I try to go the max height on my Vcore 4 500, I can only hit 415mm. I did check my configurator and I chose the Vcore 4 500 hybrid. Not sure where to else to look in the printer.cfg or RATOS.cfg
Thanks in advance!...
Solution:
Or in console do something like
g0 x50 y50 z500
Extremely inconsistent 1st Layer
I'm at a loss. My 1st layer is extremely inconsistent. I have to babystep all 1st layers the whole time. It starts good, then falls off a cliff by being way too close to the bed. On this 50x150mm patch printed in the center I started high, got a good looking layer, then the nozzle goes way too close to the bed.
It doesn't matter what material, bed temp or hotend temp, the 1st layer never is right. Usually let the printer heatsoak for 30mims before evem homing just to get all parts nice and hot.
BEACON Calibration shows a 65um gantry twist, so far the best I achieved. Going lower is extremely hard.
...
Solution:
Next update after some prints: the Toro3D Ti tube is a MUST HAVE, every 1st layer is a DREAM now! So if anyone has the same issue with very inconsistent 1st layer on the VC4 500 or the VC4 in general, drop in the Ti tube and call it a day.
Extremely high gantry twist
Hello, I'm trying to calibrate my V-core 4 500 after updating from hybrid to IDEX. During the beacon ratos calibrate i get this:
Gantry twist relative to the center
Extremely high gantry twist: 3052.809880μm....
Toolhead 1.0 Sizing Issue - vCore 3.1
Hi there, about a year ago I ordered the Toolhead v1.0 kit for the vcore 3.1 along with a hotend/extruder.
LDO Orbiter V2.0 Extruder
Phaetus Rapido 2.0 Plus UHF Hotend
Rat Rig V-Core Toolhead v1.0 - Upgrade Kit for V-Core 3.1 - Printed Parts (Orbiter/Rapido) ...
New build, strange bump on bed
Any ideas on what the Ayers Rock 3D map is doing on my new VC4 - 500 Hybrid? Nothing visible there.
V4 500 IDEX shitload of small crums
Overtightened my primary extruder and now molten filament is streaming down from the direction of the heatsink. IDEX and Remap toolheads to the rescue... so I thought.
A small print approx. 20min prints flawless, but as soon as I print a large model little wisps and strands appear several layers in and the situation gradually grows worse and worse. In the end I end up with an unusable print and a build plate literally filled with broken off and tossed around crums.
Included pictures:...
Solution:
Ok, after printing a temp tower for the second hotend I upped the temperature from 210°C (best for first hotend) to 240°C (I'm printing PETG).
Now everything prints fine on the second hotend.
Which begs a new and different question......
Belts got nibbled up a lot
Yeah so my printer is 2 years old now with the whole XY system replaced with Open Front Tensioner, Lightweight Y carriage and all metal mod.
Somehow my belt aren’t being routed right both upper and lower
I wonder where could be the main reason ? The area is pretty close to the tensioner....
Solution:
Solution: Fuck it I find it my own since our Admins are busy handling some other topics.
So you people who use this Open Front Tensioner from Funssor or EarthToMe.
Try to tension by using your fingers, pull the bearing block to the tension point then tighten the Nylon Nut under the tensioner housing. Then screw in the tension bolt at front. ...
Z-tilt Error DRV_STATUS: 001c0010
I am getting an error message when I do a Z-Tilt. The printer homes XYZ no problem but on the Z tilt it does the 1st measurement but on the 1st adjustment I get this error. Any ideas?
DRV_STATUS: 001c0010 s2vsa=1(ShortToSupply_A!) cs_actual=28...
Heater not heating as expected
Hi all, I'm having an issue where the thermistor of T0 is giving me spiky values causing a system shutdown while printing (see purple line in picture). I've now replaced the Rapido with a completely new one, but the issue continuous to happen with this one, making me wonder if it is the thermistor that is the cause of this. There are no weird kinks or anything in the cable, and the cables are properly secured. T1 is showing no issues whatsoever.
Anybody have a clue? Maybe something on the EBB42 board?...
RatOS-invalid
Have tried the version of RatOS 2.1 and followed the guide but still ended up having problems.
Used Rufus to flash the sd with the image we downloaded from github at the link in the guide. Attached you find the folder used.
Then we proceed by upgrading the software packages:
Since I found both ratos and ratos-configurator in the list (RatOS prior to V2.1.0-RC4), we started by updating ratos first, then ratos-configurator. Ended up stuck with the upgrade of the configurator....
