Not able to upload STLs/3MFs to VC4 IDEX
Not even sure where to start with this one lol. The printer is built and working other than a few issues I need to figure out but the one that is effecting my ability the most to print is not being able to upload files over RatOS.
When I try to upload the file ratOS tries to download the file but it fails every time I try. Ive tried all the normal stuff like restarting the machine and trying files that my vcore 3.1 has no issue completing the download.
SO yeah! not sure what my issues is here lol...
Power supply fried
So I think I fried my power supply....
I have a VCore 4 hybrid 300.
Mains power (I'm in the eu so 220V) gets to the power supply input but I only get ~1.5V out.
Before I order a new one and rewire stuff does anyone have any idea if I can fix it?
...
Bed Heater Wiring Confusion
Hello, I am very confused about the wiring of the bed heater. My bed heater came precrimped with 2 straight male style connectors and a 2pin JST style connector. Photo attached. The photo I included from the wiring section shows 3 forks added to the wires on the bed heater. The instructions show connecting the fork style crimps to three locations on the power supply. The commissioning guide instructs the JST 2pin connector to be inserted on the motherboard. Could someone please clarify what is n...
Error when trying to running calibration on VAOC camera, "no attribute Z_Offset_probe"
What is causing this issue? I have followed the commissioning guide.
Solution:
[z_offset_probe]
pin: ^PG10 # probe trigger pin
z_offset: -7 # probe height, used to limit the probe z-move
y_offset: 0 # probe y-offset, measured from the camera centre
x_offset: 37.5 # probe x-offset, measured from the camera centre...
Ratos Configuator update gets stuck at 91% -93%
I am trying to commission my Vcore4 and when I try to update ratos configuator it will not complete and gets tuck at 93%. When I refresh the update will complete and everything else updates ok. Then when I try to flash my board in DFU the board isn't detected. I have tried 3 Pi's, 4 new SD cards and 2O Octopus v1.1 boards all with the same result. I have also tried to flash it with a SD card with the compiled firmware and I still get board not detected. Any help with this would be very much appr...
Finish the Commissioning guide
I tried to change into the performance mode, but I can't save the changes. I think it is because both toolheads have warnings ...
Solution:
Then you should be fine
VORON IMPLEMENTATION ISSUE - BEACON CALIBRATE
Just completed my 2.4 upgrade to beacon/orbitor2/rapido2UHF to match my RatRigs currently operating. During initial Beacon Calibrate it will not QGL because the values keep increaing like the motors are not assigned correctly. I have looked @ the wiring too many times to count, verified ratos.cfg assignments, verified ratos config wizard selections. Octopus Pro 446, EBB42, PI4b, Kind of at a loss now, any insight????
Offset between walls and solid infill
Hello, I do have a massive problem with my printer. Its an IDEX500 And I have a difference between T0 and T1.
1. When printing with T1, I got massive waves of resonance within the print. But this is only to the extrusion, not due to wrong input shaping. It seems like the extruder has a resonance, not the toolhead.
2. I get an offset between walls and solid infill while printing with T1 only. the comparison between the gcode preview what the printer thinks its printing and the actual print is attached. If the printer is printing in copy or mirror mode, there is no offset between walls and the solid infill. ...
Solution:
Problems solved! The reason for the offset between the walls and the infill was broken raspberry PI.it seems like that the raspberry gave wrong comments to the main board for the second print head, the first print head absolutely fine but the second didn’t. I can’t explain why this happened but after switching to another PI 4B the problem was gone. This leads to the conclusion that the raspberry PI could lead to such issues.
Issue with belt tension graphs
Hey everyone, I'm building a V-Core 4 IDEX (currently CoreXY). Everything looked fine until I started testing belt tension. No matter what I do, the upper belt always has more tension than the lower one. At some point, the gantry became tilted and now it can’t reach the Y-axis endstop. Any ideas on how to fix this?
