Error when trying to running calibration on VAOC camera, "no attribute Z_Offset_probe"
What is causing this issue? I have followed the commissioning guide.
Solution:
[z_offset_probe]
pin: ^PG10 # probe trigger pin
z_offset: -7 # probe height, used to limit the probe z-move
y_offset: 0 # probe y-offset, measured from the camera centre
x_offset: 37.5 # probe x-offset, measured from the camera centre...
Ratos Configuator update gets stuck at 91% -93%
I am trying to commission my Vcore4 and when I try to update ratos configuator it will not complete and gets tuck at 93%. When I refresh the update will complete and everything else updates ok. Then when I try to flash my board in DFU the board isn't detected. I have tried 3 Pi's, 4 new SD cards and 2O Octopus v1.1 boards all with the same result. I have also tried to flash it with a SD card with the compiled firmware and I still get board not detected. Any help with this would be very much appr...
Finish the Commissioning guide
I tried to change into the performance mode, but I can't save the changes. I think it is because both toolheads have warnings ...
Solution:
Then you should be fine
VORON IMPLEMENTATION ISSUE - BEACON CALIBRATE
Just completed my 2.4 upgrade to beacon/orbitor2/rapido2UHF to match my RatRigs currently operating. During initial Beacon Calibrate it will not QGL because the values keep increaing like the motors are not assigned correctly. I have looked @ the wiring too many times to count, verified ratos.cfg assignments, verified ratos config wizard selections. Octopus Pro 446, EBB42, PI4b, Kind of at a loss now, any insight????
Offset between walls and solid infill
Hello, I do have a massive problem with my printer. Its an IDEX500 And I have a difference between T0 and T1.
1. When printing with T1, I got massive waves of resonance within the print. But this is only to the extrusion, not due to wrong input shaping. It seems like the extruder has a resonance, not the toolhead.
2. I get an offset between walls and solid infill while printing with T1 only. the comparison between the gcode preview what the printer thinks its printing and the actual print is attached. If the printer is printing in copy or mirror mode, there is no offset between walls and the solid infill. ...
Solution:
Problems solved! The reason for the offset between the walls and the infill was broken raspberry PI.it seems like that the raspberry gave wrong comments to the main board for the second print head, the first print head absolutely fine but the second didn’t. I can’t explain why this happened but after switching to another PI 4B the problem was gone. This leads to the conclusion that the raspberry PI could lead to such issues.
Issue with belt tension graphs
Hey everyone, I'm building a V-Core 4 IDEX (currently CoreXY). Everything looked fine until I started testing belt tension. No matter what I do, the upper belt always has more tension than the lower one. At some point, the gantry became tilted and now it can’t reach the Y-axis endstop. Any ideas on how to fix this?
TMC Stepper_z2 reports error DRV_Status during beacon calibration
VC4-400 mm build. Build is finished for the Core XY kit. I have passed the sanity checks and checked all my wiring a few times now. When I attempt a ( beacon calibration ) it starts its sequence and before finishing I lose connection to klipper due to this error. Over temp warning for the z2 stepper. Here’s some photos for reference of my wiring lol be easy on the roasting. This is my first build and I learned a lot during this. Any ideas to try or Solutions would be appreciated please and than...
Solution:
I figured it out. If your fan is not spinning during operations it’s configured wrong. I chose digital pwn on 2 pin port for the controller fan which I’ve been referring to it as the mcu fan. I have changed it to input voltage pwm on the configurator and can verify my fans are working during operations now.
Core-V4 Hybrid 500 - Commissioning Issue - no 'mainsail'
Hello,
this is my first post in discord.
I have build up my Core-V4 Hybrid 500 and now trying to commission it. Raspi is starting and I could connect to ratos.local (respectively to the static ip-adress over ethernet). A 7" BTT-Toucscreen is attached and shows klipper-screen. I could start the Setup-Wizzard. Setup ist completed and afterwards mainsail should be available - but the only display shows "initializing" forever. On klipper I could run home-x and home-y and it is working (after fixing an issue with a factory-assembled motor-cable. It seems klipper is up and running, x- and y-motors and belts are installed correct. When I run z-home, all steppermotors are start running in the same direction (looks also good), but will not stop and will bump into endposition.
...
